Matter runs over your WiFi so as long as your server you run Home Assistant on for example has wired or wireless access you are good to go. My Home Assistant is on LAN and wired so no wireless, but they all communicate through the WiFi network. if you have a Bluetooth dongle or onboard, Home Assistant would also use that to pair and communicate if needed.
2.4Ghz WiFi is only supported and no newer generations yet.
Honestly, if I have the option to keep it toggled on/off I’m fine with it, but I also don’t see it in my latest update which came in last night. But not too concerned yet (Pixel 8a) so it’s still pretty new I guess. :)
I have a TCL ROKU TV which is way too chatty on my network. It sends every single keypress on the remote to their servers (just look into the dev console which is easy enough to see what is logged). I have an adblock dns server on my network
These are just in the last 23 minutes of the hour. As I understand, it’s not always doing this if they are not blocked, but when you block them, it starts to panic!
The advantage of doing this is instead of having the ad on the right side of the home menu, I have a nice translucent adbox with nothing in it… Also, if you look up the secret codes for Roku menus, you can also toggle the ad server they use so sometimes if some slip through, you get some in house tested ones which are sometimes funny. But that’s extremely rare for us.
Our next TV will probably be a display or offline only and be a streaming box with custom firmware such as Librelec or something else when the time comes.
I test installed it in Proxmox in a Debian 12 LXC for the sever part, it was fairly easy, just run three commands. The client was as well, but failed to do something with the email during registration. It has a while longer to go I think. But I put it in my bookmarks to visit every so often as well. :)
I lost my respect for Asus when I had a Zenwatch 2 (I still have it), and they promised at the time Android Wear 2.0 in front our faces for months promising it would be released, but refused to even give an estimated time of release to OTA. This was well after WearOS 2 was released. Their online forum staff members were rude sometimes about it and other times, never responded to passionate asks about when it would be made available. The fact that they didn’t reply and care about giving any updates or indication at the time, was enough to push me far away from them.
I use Technitium DNS as both my DHCP and DNS Server on my network. I then have my ISP Router’s DHCP turned off, and point the primary DNS IP To Technitium’s on my network. I have roughly 66-67 network devices at a given time on my network, mostly wireless. (Think wiFi locks, Lights, Outlets etc) then I have my phones and gaming systems an any given thing.
To manage my IP’s I use an Airtable type of database via BaseRow, also self hosted. Through my router’s records, I copied/pasted every single MAC address I found, into a column in my BaseRow table there, and then added the device name or friendly name to another with an assigned IP I want to use. I have a more organized system of ranges 192.168.1.1-10 is mobile devices, 192.168.1.11-30 is IoT etc…
By having my network setup in this fashion, I accomplish a few things, all new devices which power on or connect to the router to get their IP assignment fail to get it since it’s turned off there, and they search the network for an available DHCP Server which lands squarely on the TechnitiumDNS server and are assigned it through there. I also have adblocking enabled through the same server so I have a more home wide adblock which works. (You’d be amazed at how much Telemetry a TV Sends out for every single remote keypress!) I have been able to block those with the adblock enabled. With the DNS server, you can also assign DHCP ranges address, it is really an overly complex server and probably overkill for a home network. I’ve only scratched the surface of what it can do.
If you don’t want to fuss with TechnitiumDNS, there’s AdguardHome, or even PiHole you can use if you want to block Ads (or you can simply disable that function) and those also act as a DHCP Server.
Or, if you are wanting to spend a few hours configuring it, you could run your own DHCP Server in a VM or dedicated device such as a Raspberry Pi.
With all of these settings, it’s important to set your DHCP lease offer long enough that if you have to reboot the DHCP Server for kernel update, or it crashes, you won’t have any devices fail as some do regular polling to check for connectivity (My Linux computer does this a lot). I don’t remember if it’s KDE or Arch. Anyway, running the DNS Server also allows you to custom build your own “domain” system if you will. So could assign maybe your self hosted Calendar for example to http://calendar.local or http://calendar.internal.
By setting up a dedicated DHCP Server, using the manual method or one of the different AdBlock systems, you can also turn off DHCP registration for ‘foreign’ devices or those which aren’t in your DHCP table. This offers a small element of extra security for your WiFi, but it’s not 100% secure if someone knows your IP ranges and Subnet Mask. Also, this will make it easier in the future for you if you upgrade your router or replace it as there’s just two settings to change. (DCHP Server off and the optional self hosted DNS).
Why not use a different DDNS service? There are plenty out there. :) I think this may solve your issue. I’ve been using freemyip.com’'s for a while and have had no problem in the past issusing LetsEncrypt SSL’s. At the moment, I’m on Cloudflare tunnels so it’s automatic with them, which I know is a huge trust issue for a lot of people, but I don’t mind it for my stuff. But I do like to have my DDNS as a backup service from time to time.
Mushroom cards
Local Tuya - so I can control my Tuya Devices without needing the cloud.
Wyze - I have a couple of cameras which are Wyze so I use it for those. I’m not against the cloud for some things. :)
Spook - not your homie – When I deactivate or rename a device (seasonally), it lets me know which dashboards need updated for example.
Playstation Network - so I can show what my PS5 and PS4 are doing while active.
Several other items such as themes I’ve tried out and probably more I’ve tried but never removed.
I have been using Tailscale, connected it to my domain, I use Authentik for my OIDC/SSO Sign in and tied it that way for the MFA OIDC Login Tailscale let’s you use. All I needed to do is setup a webfinger for it and once it verified my domain, I was able to give them my OIDC settings for them. Tailscale so far for me in the last year or so has been quite simple to use. Plus, being able to log into my admin console and any devices I enroll through Authentik’s front end, has given me peace of mind knowing it’s quite secure. (All of this on a Proxmox server BTW).
One may argue about self hosting Wireguard and I agree, it’s quite easy to do if you use something like wg-easy which makes it simple to add phones to your network. My concern with it though was having to poke a hole into my firewall for the WG traffic to hit the server, once I got into Tailscale, it’s made it easier and I don’t have any open ports on the router now. I think this is primarily why the Jupiter Broadcasting guys push it so much on their podcasts, not to mention one of the hosts on his podcast is an employee for Tailscale as well, so that probably helps a bit.
As for funding for both Nebula, or Tailscale, they do cater to enterprise customers so you have the assurance that they do have to answer to them if they revoke a service or ruin it. :)
For Tailscale, it’s just a matter of them allowing you to add 100 devices for free and it’s simple command to install it on any client via the cli including Apple TV for example. For phones, I have Tailscale on my phone connected 24/7 to my exit node which is my Proxmox server which acts as one, and as a backup, my Raspberry Pi which acts as one as well. So, even if I’m on the road or away from home, I’m always on my home network (unless blocked by overzealous sysadmins on their public WiFi networks). There’s not much to manage via the phone, but I like to think it’s ‘set and forget’ really, once you have it all configured, it just runs in the background and they do not decrypt your traffic much less care what goes through it.
I took a quick read of the comments and I apologize in advance if this has been suggested already.
I use a self hosted DNS server (AdGuardHome) I was using TechnitiumDNS for a long while, but moved over to the other recently so I could do some more blocking as needed (adult special needs house dweller sometimes needs limited internet). It also acts as a DHCP Server so it takes the role of both the DHCP assignments away from the router. As it so happens, this week, I got to experience the benefit of having this setup live when my main router also went down, I was able to switch to a spare router (My ISP provided one) and all I had to do was turn the DHCP off and optionally point the DNS To my AdGuardHome address, set the SSID’s up and I was in business. All of my devices happily reconnected and grabbed their assigned IP’s.
In short, if you have a spare computer, SBC such as a raspberry PI or whatnot, you can easily host something like that and not have to worry about setting those again.
I also use Stealth for my Reddit experience. It also doesn’t support comments or logging in. :) https://f-droid.org/packages/com.cosmos.unreddit/
Cyberchef, I’ve looked at but honestly for me, IT Tools works best for my needs so it’s all good on my end.
Dozzle is just log viewing plain and simple. Dockge shows more that’s all I know. I tested Dockge earlier on in development and haven’t been back since, I know it’s grown a lot more since.
I’ve seen a few mentions of PiHole and AdguardHome, I started on PiHole, then moved to AdguardHome for adblocking. Then I heard about and have been using TechnitiumDNS server which is sort of overkill for our needs, but with the right ad-lists, it is fantastic at blocking advertisements on my home network. Super fast install too, even on a Raspberry Pi 2 :) I run that along with Proxmox-VE (Protected behind OIDC Login) and several other containers on my cranky old Dell Desktop server.
Mostly Vaultwarden, and a few other services for home private use such as PairDrop for inter system sharing and a self destructing file sharing server for when we need to send documents to our Attorney’s (rarely but sometimes we need to) office via Pingvin.
I also run:
With Authentik setup, I can login to things like my Fresh Tomato Router TechnitiumDNS (Both use HTTP Auth headers) and Memos which uses OIDC/SSO. It’s meant to replace our Google Keep notes.
docker logs -follow command.I still use Portainer-CE and am happy there, I may try Dockage or the others, but it’s fine for what I need it for (It’s also protected by OIDC)
I’m sure I may have missed a few, but this post has gone on long enough. :)
What about bad actors which swipe the phone, and it’s behind the biometric lock? Too many failed attempts may or may not be a sign of it not working well, so if it bases part of it on the failed attempts, it would lower the chances of being further protected. I know they would ask for the pattern/pin or password to re-enroll the biometric, but let’s assume that’s already known, then game over.
You can always use something like SSHwifty It retains your logins through your browser’s session data and never on your server, but it will allow you to remote into your local system from anywhere on the WWW if you desire to do so. With Tailscale, once you are connected into your Tailnet, you can pretty much SSH into any of your devices as long as the subnet sharing flag is turned on I believe. I’ve never had any issues with mine not allowing any SSH connections.
In one way, I’m happy this is happening, in another way, I’m not - I’ve given well over 2 decades of my life to the call center way of living. Let me give you a sneak peak into what really happens in the daily life of a call center worker.
You live by the time on your telephone, it’s your punch in and punch out system in most centers. Don’t clock in more than 8 or 15 or whatever insane metrics they set past your clock in time else you will be considered tardy. This includes all breaks and clocking out.
If you are a first contact person and taking phone orders, your ‘talk time’ is measured. Anything more than the standardized 5 or 6 minutes is considered excessive and they tell you to move the calls along faster.
If you are customer service, your talk time is loosened but you are also the first and last contact the customer should have for the issue.
Your phone calls are monitored and/or recorded (For Real!). If you are like me and hate to your your voice, woe be it to you when they play back your last call or two so you can hear yourself talking to the customer. If not recorded, then it is up to the monitoring person to be nice. You are then told what you need to do to speed up your talk time, or increase sales etc…
Telemarketing
Oh dear God, this is a life sucker and has the highest turnover on jobs. You quickly learn more about human nature in an odd sense. The sheer pressure on booking that next sale is insanely high and if you don’t meet the sales minimums for the day or even hour, you are sent home without pay. I worked for a company which sold HR Manual trials, I was never more relieved and happy to be fired when I was for not making the per-requisite sales quotas for the half day.
TIPS
I don’t think I’ve encountered a single call center rep in my years of service where a CSR decided that today, they would be a jerk. All we ever want to do is get through the day and earn our wages and go home.
One thing I will say with confidence, is everyone you work with has something in common, you aren’t there necessarily because you enjoy it, you are there because it puts food on the table and beats living off of unemployment benefits. It’s a thankless job.
If you receive great service from a call center rep (CSR) and are happy, politely ask to speak with their supervisor and when you do, be sure to leave them a good review. It doesn’t always help to do this after a bad call, but sometimes rebounding to a new agent by calling the company back and asking for a supervisor will make a big difference if you take issue with them about the poor quality of service you received.
Remember, if you can’t resolve an issue with a CSR, It’s not always that they don’t want to resolve the issue for you, their hands are probably tied and in fear of losing their job or being reprimanded, they simply won’t budge.
Kindness goes a long way with us as well, if you are respectful and kind, we reflect the same back to you and often have tools at our disposal to grant you an extra discount and/or savings. We genuinely want to see you happy!
ON THE OTHER HAND
If putting AI in front of the call centers will help screen out the most common issues, then by all means do it. Also, if the stupid bean counters out there which insist of outsourcing to third world countries as it’s cheaper, can find it to be more cost effective to use AI, and keep the jobs local to their country of operation, then I’m in favor of it.
Homebox - before we relocate - whenever that is, I will be printing labels and putting them under and behind my stuff, scanning it into there and then will use that to keep track of our items after the move to know what is in which box etc.
NocoDB Self Hosted (I use this for a few things) - started out with my network ip’s I have on my servers and ports for my containers and most recently a sleep log.
Just a couple there.
Grafana + Prometheus dashboards can be quite addicting or useful. Noted.lol put together a nice tutorial for getting started.
For most of my services though, I simply use Uptime Kuma which then sends an alert to Gotify when my services go down or whatnot, Gotify then instantly notifies my phone so I can be aware. It helps keep the spouse happy when their go to service for some reason crashed. :)
Good to know about the 5Ghz WiFi on the newer devices.
I’m still new to Matter so I appreciate the info you gave for not all devices not using WiFi. :)